Glass Door Roller Installation and Removal Guide

Glass Door Roller Hardware How to Guides Hardware Department

Glass Door Roller Installation and Removal Guides

This guide will help you remove your old roller. This is the best way for you to find the exact roller you need for your door. With over 300 rollers you need to take your old one out. Then Use our Glass Door Roller Selection Guide. Click Here

Glass Door Roller Installation and Removal Guide Type 1

Step 1 Remove the door from the frame. Lester Says " Look for anti lift blocks in the top of the frame.  Most doors can be removed from the open position without removing the anti lift blocks. Glass doors are very heavy it is recommended that you have help! Lift the door up and pull it out of the frame.   Lay the door flat on the ground.

Step 2 Remove any mount screws from the roller.  Lester Says "Not all doors use mounting screws.

Using a screw driver pry the side tabs on both sides of the roller assembly down so that the roller can be pry ed down and out of the door channel. Lester Says " Spray some type of lubricant on the roller if it is rusty or corroded to help you with the removal"

Top Tab Style below

Step 3 Pre adjust the roller to the same configuration as your old roller and the push the new roller into place.  Lester Says "You can use a a hammer to tap! the roller into place Remember you are working on a glass door! Reinstall the mounting screw if you removed one.

Step 4 Reinstall the door into the frame. 

Step 5 If the door is not Square use the hole in the end of the door to adjust the roller adjustment screw.

Step 6 In some cases you may need to adjust the lock strike.  Loosen the screws on the latch on the frame and line them up for proper locking.

Step 7 If you removed any anti lift blocks make sure to reinstall them for security purposes. Lester Says " With out them the door could just be lifted out!"

Glass Door Roller Installation and Removal Guide Type 2

Step 1 Remove the door from the frame. Lester Says " Look for anti lift blocks in the top of the frame.  Most doors can be removed from the open position without removing the anti lift blocks. Glass doors are very heavy it is recommended that you have help! Lift the door up and pull it out of the frame.   Lay the door flat on the ground.

Step 2 Remove any mount screws from the roller.  Lester Says "Not all doors use mounting screws.

Using a screw driver pry the side tabs on both sides of the roller assembly down so that the roller can be pry ed down and out of the door channel. Lester Says " Spray some type of lubricant on the roller if it is rusty or corroded to help you with the removal"

Hook Tab Style below

Step 3 Pre adjust the roller to the same configuration as your old roller and the push the new roller into place.  Lester Says "You can use a a hammer to tap! the roller into place Remember you are working on a glass door! Reinstall the mounting screw if you removed one.

Step 4 Reinstall the door into the frame. 

Step 5 If the door is not Square use the hole in the end of the door to adjust the roller adjustment screw.

Step 6 In some cases you may need to adjust the lock strike.  Loosen the screws on the latch on the frame and line them up for proper locking.

Step 7 If you removed any anti lift blocks make sure to reinstall them for security purposes. Lester Says " With out them the door could just be lifted out!"

Glass Door Roller Installation and Removal Guide Type 3

Step 1 Remove the door from the frame. Lester Says " Look for anti lift blocks in the top of the frame.  Most doors can be removed from the open position without removing the anti lift blocks. Glass doors are very heavy it is recommended that you have help! Lift the door up and pull it out of the frame.   Lay the door flat on the ground.

Step 2 Remove any mount screws from the roller.  Lester Says "Not all doors use mounting screws.

Using a screw driver pry the side tabs on both sides of the roller assembly down so that the roller can be pry ed down and out of the door channel. Lester Says " Spray some type of lubricant on the roller if it is rusty or corroded to help you with the removal"

Step 3 Pre adjust the roller to the same configuration as your old roller and the push the new roller into place.  Lester Says "You can use a a hammer to tap! the roller into place Remember you are working on a glass door! Reinstall the mounting screw if you removed one.

Step 4 Reinstall the door into the frame. 

Step 5 If the door is not Square use the hole in the end of the door to adjust the roller adjustment screw.

Step 6 In some cases you may need to adjust the lock strike.  Loosen the screws on the latch on the frame and line them up for proper locking.

Step 7 If you removed any anti lift blocks make sure to reinstall them for security purposes. Lester Says " With out them the door could just be lifted out!"

Glass Door Roller Installation and Removal Guide Type 4

Step 1 Remove the door from the frame. Lester Says " Look for anti lift blocks in the top of the frame.  Most doors can be removed from the open position without removing the anti lift blocks. Glass doors are very heavy it is recommended that you have help! Lift the door up and pull it out of the frame.   Lay the door flat on the ground.

Step 2 Remove any mount screws from the roller.  Lester Says "Not all doors use mounting screws.

Using a screw driver pry the side tabs on both sides of the roller assembly down so that the roller can be pry ed down and out of the door channel. Lester Says " Spray some type of lubricant on the roller if it is rusty or corroded to help you with the removal"

Step 3 Pre adjust the roller to the same configuration as your old roller and the push the new roller into place.  Lester Says "You can use a a hammer to tap! the roller into place Remember you are working on a glass door! Reinstall the mounting screw if you removed one.

Step 4 Reinstall the door into the frame. 

Step 5 If the door is not Square use the hole in the end of the door to adjust the roller adjustment screw.

Step 6 In some cases you may need to adjust the lock strike.  Loosen the screws on the latch on the frame and line them up for proper locking.

Step 7 If you removed any anti lift blocks make sure to reinstall them for security purposes. Lester Says " With out them the door could just be lifted out!"

Installation Instructions

Step 1 Remove the door from the frame. Lester Says " Look for anti lift blocks in the top of the frame.  Most doors can be removed from the open position without removing the anti lift blocks. Glass doors are very heavy it is recommended that you have help! Lift the door up and pull it out of the frame.   Lay the door flat on the ground.

Step 2 Remove any mount screws from the roller.  Lester Says "Not all doors use mounting screws.

Using a screw driver pry the side tabs on both sides of the roller assembly down so that the roller can be pry ed down and out of the door channel. Lester Says " Spray some type of lubricant on the roller if it is rusty or corroded to help you with the removal"

Straight Tab Style below

Step 3 Pre adjust the roller to the same configuration as your old roller and the push the new roller into place.  Lester Says "You can use a a hammer to tap! the roller into place Remember you are working on a glass door! Reinstall the mounting screw if you removed one.

Step 4 Reinstall the door into the frame. 

Step 5 If the door is not Square use the hole in the end of the door to adjust the roller adjustment screw.

Step 6 In some cases you may need to adjust the lock strike.  Loosen the screws on the latch on the frame and line them up for proper locking.

Step 7 If you removed any anti lift blocks make sure to reinstall them for security purposes. Lester Says " With out them the door could just be lifted out!"

Glass Door Roller Installation and Removal Guide Type 6

Step 1 Remove the door from the frame. Lester Says " Look for anti lift blocks in the top of the frame.  Most doors can be removed from the open position without removing the anti lift blocks. Glass doors are very heavy it is recommended that you have help! Lift the door up and pull it out of the frame.   Lay the door flat on the ground.

Step 2 Remove any mount screws from the roller.  Lester Says "Not all doors use mounting screws.

Using a screw driver pry the side tabs on both sides of the roller assembly down so that the roller can be pry ed down and out of the door channel. Lester Says " Spray some type of lubricant on the roller if it is rusty or corroded to help you with the removal"

Smooth Plain Back Style below

Step 3 Pre adjust the roller to the same confiquration as your old roller and the push the new roller into place.  Lester Says "You can use a a hammer to tap! the roller into place Remember you are working on a glass door! Reinstall the mounting screw if you removed one.

Step 4 Reinstall the door into the frame. 

Step 5 If the door is not Square use the hole in the end of the door to adjust the roller adjustment screw.

Step 6 In some cases you may need to adjust the lock strike.  Losen the screws on the latch on the frame and line them up for proper locking.

Step 7 If you removed any anti lift blocks make sure to reinstall them for security purposes. Lester Says " With out them the door could just be lifted out!"

Glass Door Roller Installation and Removal Guide Type 7

Step 1 Remove the door from the frame. Lester Says " Look for anti lift blocks in the top of the frame.  Most doors can be removed from the open position without removing the anti lift blocks. Glass doors are very heavy it is recommended that you have help! Lift the door up and pull it out of the frame.   Lay the door flat on the ground.

Step 2 Remove any mount screws from the roller.  Lester Says "Not all doors use mounting screws.

Using a screw driver pry the side tabs on both sides of the roller assembly down so that the roller can be pry ed down and out of the door channel. Lester Says " Spray some type of lubricant on the roller if it is rusty or corroded to help you with the removal"

Angled Tab Back Style below

Step 3 Pre adjust the roller to the same confiquration as your old roller and the push the new roller into place.  Lester Says "You can use a a hammer to tap! the roller into place Remember you are working on a glass door! Reinstall the mounting screw if you removed one.

Step 4 Reinstall the door into the frame. 

Step 5 If the door is not Square use the hole in the end of the door to adjust the roller adjustment screw.

Step 6 In some cases you may need to adjust the lock strike.  Losen the screws on the latch on the frame and line them up for proper locking.

Step 7 If you removed any anti lift blocks make sure to reinstall them for security purposes. Lester Says " With out them the door could just be lifted out!"

Glass Door Roller Installation and Removal Guide Type 8

Step 1 Remove the door from the frame. Lester Says " Look for anti lift blocks in the top of the frame.  Most doors can be removed from the open position without removing the anti lift blocks. Glass doors are very heavy it is recommended that you have help! Lift the door up and pull it out of the frame.   Lay the door flat on the ground.

Step 2 Remove any mount screws from the roller.  Lester Says "Not all doors use mounting screws.

Using a screw driver pry the side tabs on both sides of the roller assembly down so that the roller can be pry ed down and out of the door channel. Lester Says " Spray some type of lubricant on the roller if it is rusty or corroded to help you with the removal"

U Notch Back Style below

Step 3 Pre adjust the roller to the same confiquration as your old roller and the push the new roller into place.  Lester Says "You can use a a hammer to tap! the roller into place Remember you are working on a glass door! Reinstall the mounting screw if you removed one.

Step 4 Reinstall the door into the frame. 

Step 5 If the door is not Square use the hole in the end of the door to adjust the roller adjustment screw.

Step 6 In some cases you may need to adjust the lock strike.  Losen the screws on the latch on the frame and line them up for proper locking.

Step 7 If you removed any anti lift blocks make sure to reinstall them for security purposes. Lester Says " With out them the door could just be lifted out!"

Glass Door Roller Installation and Removal Guide Type 9

Step 1 Remove the door from the frame. Lester Says " Look for anti lift blocks in the top of the frame.  Most doors can be removed from the open position without removing the anti lift blocks. Glass doors are very heavy it is recommended that you have help! Lift the door up and pull it out of the frame.   Lay the door flat on the ground.

Step 2 Remove any mount screws from the roller.  Lester Says "Not all doors use mounting screws.

Using a screw driver pry the side tabs on both sides of the roller assembly down so that the roller can be pry ed down and out of the door channel. Lester Says " Spray some type of lubricant on the roller if it is rusty or corroded to help you with the removal"

Hook Back Style below

Step 3 Pre adjust the roller to the same confiquration as your old roller and the push the new roller into place.  Lester Says "You can use a a hammer to tap! the roller into place Remember you are working on a glass door! Reinstall the mounting screw if you removed one.

Step 4 Reinstall the door into the frame. 

Step 5 If the door is not Square use the hole in the end of the door to adjust the roller adjustment screw.

Step 6 In some cases you may need to adjust the lock strike.  Losen the screws on the latch on the frame and line them up for proper locking.

Step 7 If you removed any anti lift blocks make sure to reinstall them for security purposes. Lester Says " With out them the door could just be lifted out!"

Glass Door Roller Installation and Removal Guide!