1/2 Inch to 1 Inch Nipples

These are pieces of pipe cut at specific lengths and threaded at both ends in 1/2 Inch, 3/4 Inch, and 1 Inch diameters.

Plumbing Galvanized Pipe Fittings 1 1/4 Inch to 2 Inch Nipples

1-1/4 Inch to 2 Inch Nipples

These are pieces of pipe cut at specific lengths and threaded at both ends in 1 1/4 Inch, 1 1/2 Inch and 2 Inch diameters.

Plumbing Galvanized Pipe Fittings 2 1/2 Inch to 4 Inch Nipples

2-1/2 Inch to 4 Inch Nipples

These are pieces of pipe cut at specific lengths and threaded at both ends in 2 1/2 Inch, 3 Inch, and 4 Inch diameters.

Plumbing Galvanized Pipe Fittings 90 Degree Elbows

90 Degree Elbows

We have all standard pipe sizes of these so you can make a right angle turn in your pipe run.

Plumbing Galvanized Pipe Fittings 45 Degree Elbows

45 Degree Elbows

For a 45 degree turn in your pipe run you need one of these.

Plumbing Galvanized Pipe Fittings Couplings

Couplings

All standard pipe sizes of internally threaded couplings for you to attach one piece of threaded pipe to another.

Plumbing Galvanized Pipe Fittings Street Elbows

Street Elbows

These elbows have male threads at one end and female threads on the other end and are available in both 45 degrees and 90 degrees and in all standard pipe sizes.

Plumbing Galvanized Pipe Fittings Cross

Cross

This fitting allows you to split a single pipe run into three different directions 90 degrees to the right and 90 degrees to the left and straight ahead and are available in all standard pipe sizes.

Plumbing Galvanized Pipe Fittings Unions

Unions

A union is a three piece fitting allowing you to connect one piece of pipe to another where a standard coupling is difficult or impossible to use and are available in all standard pipe sizes.

Plumbing Galvanized Pipe Fittings Tees

Tees

These allow you to split a pipe run into two directions or combine two pipe runs into one direction and are available in all standard pipe sizes.

Plumbing Galvanized Pipe Fittings Wyes

Wyes

These allow you to tap one pipe run into another at a 45 degree angle and are available in all standard pipe sizes.

Plumbing Galvanized Pipe Fittings Plugs

Plugs

These are male threaded plugs and are designed to thread into a coupling or other fitting with female threads to cut off the flow and are available in all standard pipe sizes.

Plumbing Galvanized Pipe Fittings Lock Nuts

Lock Nuts

These are threaded nuts and come in all standard pipe sizes.

Plumbing Galvanized Pipe Fittings Floor Flanges

Floor Flanges

These allow you to securely fasten a piece of pipe to the floor or other surface and are available in all standard pipe sizes.

Plumbing Galvanized Pipe Fittings Caps

Caps

These are female threaded fittings designed to thread onto the end of a male threaded pipe to stop the flow and are available in all standard pipe sizes.

Plumbing Galvanized Pipe Fittings Reducer Couplings

Reducer Couplings

These are female threaded fittings with a different pipe size on each end in a variety of combinations to enable you to reduce or enlarge your pipe run from one size to another.

Plumbing Galvanized Pipe Fittings Reducer Bushings

Reducer Bushings

These allow you to reduce or enlarge the size of your pipe run with female threads for the smaller size and male threads for the larger size and are available in a variety of size combinations.

Plumbing Galvanized Pipe Fittings Right and Left Thread Couplings

Right and Left Thread Couplings

These are designed to be used in conjunction with right and left threaded nipples and allow you to connect two pieces of pipe by turning the coupling in only one direction.

Plumbing Galvanized Pipe Fittings Right and Left Thread Nipples

Right and Left Thread Nipples

You need these when working with right and left thread couplings and are available in most standard pipe sizes.

Plumbing Galvanized Pipe Fittings Reducer Nipples

Reducer Nipples

These are pieces of pipe in short lengths threaded on both ends with two different pipe sizes to reduce or enlarge the size of your pipe run and are available in several different size combinations.

Plumbing Galvanized Pipe Fittings Side Outlet Elbows

Side Outlet Elbows

These elbows have third female threaded opening and they are available in most standard pipe sizes.

Plumbing Galvanized Pipe Fittings Side Outlet Tees

Side Outlet Tees

These Tees have a fourth opening with female threads and are available in several pipe sizes.

Plumbing Galvanized Pipe Fittings Extensions

Extensions 

These are fittings with female threads on one end and female threads on the other designed to extend your pipe slightly and are available in 1/2 Inch and 3/4 Inch.